There are more than 4 kinds of tooth scissors, but the main function is only one thin hair.
The number of teeth in general tooth scissors is between 27-40 teeth (the most commonly used species). The number of teeth is the percentage of hair that can be cut off when you cut it down. In other words, a 35-tooth scissor thins about 35 percent of your hair, and so on.
2.Shape of Tooth Mouth
The shape of the mouth determines the structure of the hairstyle after pruning. Common teeth mouth has flat mouth, V word mouth and U word mouth. Flat mouth is a relatively early design, because the shears open and close when the hair will slip away from the mouth of the teeth, so the proportion of thinning is not standard. The V-shaped and U-shaped teeth have grooves, which can fix the hair proportionally in the teeth. The other blade cuts the hair in the teeth, and the hair outside the teeth will slide naturally. These two kinds of teeth have many uses. They can be used in the top and bangs to achieve a more natural effect and can meet the requirements of natural pruning.
3.Width of Tooth Mouth
In general, the width of the tooth scissors is 1-1.2 MNM (fine teeth), and the groove position can only accommodate 1 to 2 hair. But in some special designs, the width of the teeth is 3-5mm (thick teeth), the groove position can accommodate 5-10 hair, the number of scissors is as low as 7-14, these scissors are designed for some special hairstyle structure. The use of coarse tooth scissors can make the top shape of short hair style reach a very strong sense of mixing and hierarchy.
4.Reverse and Double Teeth
When holding the scissors with the right hand, the scissors are located on the blade held by the ring finger, while the reverse scissors are just the opposite. The scissors are located on the blade held by the thumb, that is, when the blade is opened, the reverse scissors are located above and the blade is below. The two blades of bilateral tooth scissors are all shear teeth. The main purpose of designing these two kinds of tooth scissors is to reduce the cutting line when the hair is thin. For example, take some layered hair from the sides of the head or from the back of the brain. Cut it off with the orthodontic teeth and pull it out. You can find a dotted line in the lower part of the head. This is formed when the blade is cut from top to bottom. The front of the reverse tooth scissors does not show a tangent line on the bottom surface. Double sided tooth scissors do not appear tangents because there is no blade. But because the front teeth collide with each other, they are easy to damage. These two kinds of tooth scissors are best suited for short hairstyle thin and medium short hairstyle trimming on both sides and hindbrain.
The usage of hairdressing scissors:
1.Technology of Hairpin Scissors Clip
First of all, we use our fingers to clip the part of the hair, to determine how long the hair should stay, then we should pay attention to the clip of each hair to be straight, clip the hair to pay attention to each other, and clip the angle of the hair clip is better, to avoid disjointing phenomenon, then we should pay attention to the relationship between the angle and level of subtraction The layers and angles of the hair are arranged so that we can choose the angle better, and our top hair can be vertical upward to distinguish horizontal trim, but also form a more moderate level, and the hair on both sides can be vertical trim, different angles show different levels can be 90 degrees of vertical Straight pruning, this level is also moderate.
2.Haircut Scissors Technology
First of all, we have to grab the base of the hair, determine the size of the base hair, and then we decide how much radian to form after the haircut? Generally speaking, if we grab the base of the hair is larger, the curvature of the haircut after the haircut is larger. On the contrary, if we grab the base of the hair is smaller, haircut. After the formation of the radian is also relatively small, we need to grasp the scissors at different parts of the time, so that we can form a different radian, after that, we will also have a certain level of activity, tied up the hair scissors fall to the right part, not too high or too low, if too high or too high Low will affect the length of the hair and the radian formed.
3.Trimming of Haircut Scissors
For contour trimming first we must comb the hair, then according to the requirements will be divided into several parts of the hair, the whole view of each part of the hair, and then determine what kind of trimming program, at this time we will appear a whole contour, the redundant parts of each part of the program will be cut off, this When we cut the outline out, then we compare, then adjust the layers and thickness, so that we can make the outline of the hair more perfect.