Molex Micro-Fit 3.0 to J1708 6 Pin Gray Female and Male Connector Plug Cable Assembly

Model NO.
Deutsch J1708 6 gray
Material Shape
Flat Wire
Range of Application
Transport Package
HS Code
We are proud of the superior customer gratification and wide acceptance due to our persistent pursuit of top of the range both of those on merchandise and service for Molex Micro-Fit 3.0 to J1708 6 Pin Gray Female and Male Connector Plug Cable Assembly, The product will supply to all over the world, such as: Islamabad, Curacao, Zurich, With the spirit of "credit first, development through innovation, sincere cooperation and joint growth", our company is striving to create a brilliant future with you, so as to become a most valuable platform for exporting our goods in China!
Edgar Auto Harnesses Ltd. Diamond / Audited Supplier
Molex Micro-Fit 3.0 to J1708 6 Pin Gray Female and Male Connector Plug cable assembly

1.voltage :dc 300v 5m ohm/10 ms resistance:3.0 ohm MAX
3.100% open ,Short ,Mis-Wirs Testing

SAE standards documents on OBD-II

  • J1708 – Defines a standard used for serial communications between ECUs on a heavy duty vehicle and also between a computer and the vehicle.
  • J1850 – Defines a serial data protocol. There are two variants- 10.4 kbit/s (single wire, VPW) and 41.6 kbit/s (two wire, PWM). Mainly used by US manufacturers, also known as PCI (Chrysler, 10.4 kbit/s), Class 2 (GM, 10.4 kbit/s), and SCP (Ford, 41.6 kbit/s)
  • J1939 - Defines a data protocol for heavy duty commercial vehicles
  • J1962 – Defines the physical connector used for the OBD-II interface.
  • J1978 – Defines minimal operating standards for OBD-II scan tools
  • J1979 – Defines standards for diagnostic test modes
  • J2012 – Defines standards trouble codes and definitions.
  • J2178-1 – Defines standards for network message header formats and physical address assignments
  • J2178-2 – Gives data parameter definitions
  • J2178-3 – Defines standards for network message frame IDs for single byte headers
  • J2178-4 – Defines standards for network messages with three byte headers*
  • J2284-3 – Defines 500 kbit/s CAN Physical and Data link layer
  • J2411 – Describes the GMLAN (single-wire CAN) protocol, used in newer GM vehicles. Often accessible on the OBD connector as PIN 1 on newer GM vehicles.

DEUTSCH HD10 series connector 

The HD series is an environmentally silicone rubber sealed, thermoplastic cylindrical connector, which is designed to be a faster, easier, trouble free assembly diagnostic connector in heavy-duty industry like truck, bus, cross-country vehicle,crane and forklift etc. When mated, the contacts are protected from water, dust, lubricating oils, fuel, road salt, grease, mud and other contaminants encountered.

  • Operating at temperatures -40ºC to +125ºC, no Cracking, Chipping or leaking after 20 test cycles from -40ºC~+125ºC.
  • No unlocking or unmating and exhibits no mechanical or physical damage after sinusoidal vibration levels of 20 Gs at 10 to 2000Hz in each of the three mulually perpendicular planes for 2 hours. Force testing report as below shows
  • IP68 rating, waterproof withstand immersion under 1.2 meter of water for 24 hours.


Cavity  Overall Length
Overall Height
Overall Length
Overall Height
3 1.609 (40.87)  1.069 (27.15)  1.639 (41.63)  .851 (21.62)
4 1.639 (41.63)  1.595 (40.51)  1.639 (41.63)  1.281 (32.54)
5 1.609 (40.87)  1.218 (30.94)  1.639 (41.63)  1.001 (25.43)
6 1.619 (41.12)  1.453 (36.91)  1.639 (41.63)  1.141 (28.98)
9 1.609 (40.87)  1.593 (40.47)  1.639 (41.63)  1.281 (32.54)

HD10 series

Position Contact
Plug Receptacle
no  HD16-3-16S  HD14-3-16P  -
yes  HD16-3-96S  HD14-3-96P  HD10-3-96P
4 4/16 yes  HD16-4-4S  HD10-4-4P
5 16 no  HD16-5-16S  HD14-5-16P  HD10-5-16P
6 16 yes  HD16-6-96S  HD14-6-96P  HD10-6-96P
6 12 yes  HD16-6-12S-B010  HD14-6-12P  HD10-6-12P
no  HD16-9-16S  HD14-9-16P  HD10-9-16P
yes  HD16-9-96S  HD14-9-96P  HD10-9-96P
9 (J1939)  16 yes  HD16-9-1939S  HD14-9-1939P  HD10-9-1939P



 Privately held company, established in 1999
 Sales volume over 16 Million USD since 2017 
 OEM & ODM company, with employees more than 250 persons, 7260 square-meters in size 
 Service for economical solutions and innovative wire harnesses design & manufacturing 
IATF16949 (2016) & ISO 9001 (2015), and UL certified supplier with wiring No. E468011 & cable No. E479323



1. Q: Can you help to design?
A: Yes, we are an ODM / OEM company, beyond we have been specializing in wire harness & Cable assembly since 1999.
2. Q: When will you start to help design?
A: We sketch simple solution for initial discussion, after quotation and order placed then start to drawing and double confirm with client for the design. 
3. Q: What if quality issues occur when customer discover?
A: Our quality and engineer team will positively respond for the quality issues with 72 hours, as we are intend to make long-stand strategy with customer and the value is to provide better service.
4. Q: Do you have any standard products to cut down customers lead time for prototype and tooling cost?
A: Yes, there are over 1000 sets of molds and some of them can be used for customer directly. Moreover, Edgar is specialized in wire harness over 20
years with  5000+  products